Home > Hard Drive > Running An IDE Drive As Slave To A SATA?

Running An IDE Drive As Slave To A SATA?

Contents

You can Right-Click on these drive letters and choose to Format these drives from the menu shown. In this edition of Hardware Upgrade, we’ll try and quickly squash as many common problems that we can. This may still occur even if you are installing a single drive. Jun 10, 2008 #19 (You must log in or sign up to reply here.) Show Ignored Content Topic Status: Not open for further replies. http://osuweb.net/hard-drive/problem-with-a-slave-drive.php

Apr 25, 2007 #15 Daemon6 TS Rookie Topic Starter SNGX1275 said: Thats the whole point of this thread. THen i removed them as backup storage.Everything was now on my 160/3 Sataii.Roms where then F and G.Click to expand... 3 partitions on SATA? Behaviors of boards with both PATA and SATA sockets depend on the motherboard firmware and BIOS. Others will have a note on the drive label instead: Figure Out Your Existing IDE Scheme It’s more than likely you currently have both a CD-ROM drive and hard disk plugged http://www.tomshardware.com/forum/290702-32-using-slave-sata

How To Connect Ide Hard Drive To Sata Motherboard

You probably just need to format the drive - provided of course that you can see it in Disk Management. Facebook Google+ Twitter YouTube Subscribe to TechSpot RSS Get our weekly newsletter Search TechSpot Trending Hardware The Web Culture Mobile Gaming Apple Microsoft Google Reviews Graphics Laptops Smartphones CPUs Storage Cases Depending on the model, you might need to secure the drive directly to the bay with two Phillips screws on each side. You can guess the result.-> Also, XP will mark the drive as non-bootable and others weep as they have to repair it when they stick it back in the old machine.Bob

You’ll have to install drivers for the PCI card either in or when you install the operating system. Insert the Windows XP CD into the CD-ROM drive and restart the system Follow the onscreen prompts until the partition list screen is displayed You should see your hard drive listed Note: Users installing an ATA/100 drive: Windows 2000 by default does not support ATA/100 data transfer rates. Motherboard With Ide And Sata Ports Steele also holds certifications as a Microsoft-certified desktop support technician, Microsoft-certified IT professional, Windows 7 enterprise support technician and CompTIA A+ IT technician.

The power cable you will plug in has four female plugs in it, and will only go in one way due to the shape of it, so that shouldn’t be too On rare occasions you'll run into a system with the drives packed so tightly they lack sufficient clearance. Note: You wouldn’t normally run devices outside of the case like this, but for the purposes of checking if they work, it’s a lot easier than unscrewing them and poking around this contact form Note: If you are formatting using the FAT32 file system, partitions cannot be larger than 32GB.

Click on Drive options (advanced). How Many Hard Drives Can Be Connected To A Single Ide Cable So i reinstalled Win 7, enable LBA form BIOS Setup and thats it. by RJSheppard / July 23, 2005 1:30 AM PDT In reply to: Mixing SATA and IDE drives in a system? Also, your mainboard has a maximum of gigabytes that can be seen in you BIOS - many earlier ones stopped at 200 gig (Believe it or not) you might want to

Sata And Ide Hard Drives Together

Start-> Control Panel-> Administrative Tools-> Computer Management -> Disk Management. http://smallbusiness.chron.com/connect-sata-hard-disk-slave-56859.html When running more than one OS on multiple drives you can use this option, or if running a properly installed NT/2000/XP, you can add boot options into the boot.ini. How To Connect Ide Hard Drive To Sata Motherboard WOW hope yer not to confused Daemon6 you will not find master /slave in the bios just a boot priority order I can't tell anymore ,but if you have this listed Ide And Sata Drives In Same Computer This allows the drive to be used in a RAID configuration and a signature to be written to it from operating system.

The molex connector on the right is not exclusively “IDE Power.” Either power connector will carry the juice to your drive. news Step-by-step instructions follow below: Insert the Windows 2000 CD into the CD-ROM drive and restart the system. Start Windows 7 and allow the Operating System to boot to the desktop. Don't image or old drive to the new one. Ide Hard Drive Jumper Settings

Line the new drive up with the opening of the drive bay and gently slide it into position, push it all the way in until the front of the drive is I was told because I wiped out a registry entry (related to the SATA drive setup) and there was a problem due to the fact Windows 2000 can't see anything over Box 4260 Houston, Texas 77210–4260 © Copyright 2017 Hearst Newspapers, LLC Login _ Social Sharing Find TechSpot on... have a peek at these guys Other Issues: Obviously we’ve tried to list as many issues as possible.

Ask a Question See Latest Posts TechSpot Forums are dedicated to computer enthusiasts and power users. Use Ide Drive With Sata Motherboard Make sure also that the IDE unit is NOT in the boot sequence anywhere. You should already have your primary (C:) partition defined with extra space left over as Unpartitioned Space.

Click Next to continue.

Drive enclosure for permanent use. My primary was a SATA and 2nd hd bay was an IDE. You can use those tools to label the drive. How To Make Ide Boot Instead Of Sata Master/Slave settings tell the computer which drives respond to which commands, and are therefore critical.

Edit the partition size. The SATA controllers are usually labeled SATA1, SATA2 and so on. On the article itself, two comments: 1. check my blog I'm using 3 maxtor HD's 80 & 120 gb sata + 200 gb pata, and 3 dvd burners BENQ 1625, & 1610, + LG GSA 4163B.

My two IDE hard drives (the "new" Western Digital 80Gb with XP on it and a Western Digital 250Gb with no OS) are now on one channel.