Home > Hard Drive > Installed New HDD > OS Won't Boot Up - Please Help

Installed New HDD > OS Won't Boot Up - Please Help

Contents

Now the cursor doesn't even blink on the screen, the screen is just blank. If the recovery environment won't load or doesn't see your hard drive, you likely have a hardware problem. other application software if you have any, can be installed after these are installedi assume you may not have as much access to this website since your pc is dead, here Where Windows XP might have stopped in its tracks when faced with this problem, modern versions of Windows will try to automatically run Startup Repair. have a peek at these guys

My System Specs OS ME/XP/Vista/Win7 . I will answer your questions the best I can. I would greatly appreciate if anyone has any suggestions to help me revive my hard drive, old or new. Double-check, too, that the charger is the right one for your laptop. http://www.tomshardware.com/forum/12869-63-after-installing-hard-drive-windows-boot

Computer Won't Boot With Second Hard Drive

If you can see the coloured wires inside the black outer protection, it could be time to buy a new PSU. If no errors are reported click on the Repair Permissions button. The blinking cursor is now gone. (I was concerned that the monitor decided to fail but I did troubleshoot the monitor by connecting it to the computer I am borrowing and Click on the Options button, set the partition scheme to GUID then click on the OK button.

May 30, 2013 8:51 AM Helpful (0) Reply options Link to this post by Kappy, Kappy May 30, 2013 3:23 PM in response to jsilva3071 Level 10 (275,339 points) Desktops May Join Forum | Login | Today's Posts | Tutorials | Windows 10 Forum | Windows 8 Forum Welcome to Windows 7 Forums. Occasionally, people have found that removing the drive and putting it in the freezer for a couple of hours (in a freezer bag) does the trick. Pc Won't Boot From Hard Drive Privacy Policy Terms of Use Sales and Refunds Legal Site Map Contact Apple Please click here if you are not redirected within a few seconds.

emgineeringDec 23, 2014, 1:22 PM buzznut said: Just put the hard drive back in and run the install disc. Open Menu Close Menu Apple Shopping Bag Apple Mac iPad iPhone Watch TV Music Support Search apple.com Shopping Bag : CommunitiesSign inPostBrowse discussionsContact SupportSearchCommunitiesContact SupportSign inContentPeopleSearch Support CommunitiesNotebooksMacBook Pro Please enter You can try pulling the computer's hard drive, inserting it into another computer, and recovering your files that way. http://www.tomshardware.com/answers/id-2438959/installed-hard-drive-black-screen.html not booting after installing new MSI GTX 750ti Boot problems after installing new video card.

OS X Mountain Lion (10.8.2) Posted on May 29, 2013 10:36 PM Reply I have this question too Q: New Hard drive won't boot! Hard Drive Detected In Bios But Won't Boot solved Hard Drive crashed, installed new one, now what? If you’re not sure, and there’s no power indicator on the battery itself, then remove it entirely and just use the mains charger. I followed your instructions. - I reordered the disk boot priority in BIOS. - In DISKPART, I made the SSD active and the HDD inactive. - I ran Startup Repair 2x.

Installed New Hard Drive And It Wont Boot

Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Open Disk Utility from the Utilities folder. 2. Computer Won't Boot With Second Hard Drive I did the press windows key + b + power button. New Hard Drive Won't Boot Windows If you're lucky, one of these steps may fix your software problem and allow you to boot Windows normally.

If it boots fine with one drive and not with two, you’re probably overloading the power supply. More about the author After replacing the CMOS battery (which was failing) and resetting the bios clock, he told me to take the computer home and start by connecting only the mouse, keyboard, monitor and However, it does read the drive when I go into disk utility from the internet recover. The model # on the back of the computer is MFATXSTL EL2500X. Installed A New Hard Drive Now Computer Won't Turn On

Can't find your answer ? Thanks in advance, rhit My System Specs OS Windows 7 x64 CPU Core i7 950 @ 4Ghz Motherboard Asus P6X58D Premium Memory Corsair Dominator 12Gb Graphics Card EVGA GTX 680 SC Click on the Erase button. http://osuweb.net/hard-drive/hard-drive-usage-goes-from-37g-to-71g-with-no-added-programs-installed.php Otherwise, click on the Partition tab in the DU main window. 3.

Book your tickets now and visit Synology. Computer Won't Boot From Hard Drive Thank you again for your help, Colette 0 #4 cbarnard Posted 25 April 2009 - 08:54 PM cbarnard Member Member 755 posts Hello Colette,Thank you for more information...Does your gateway have Can you get the SSD to boot itself by setting first to boot in BIOS, then trigger the HD using F8 key as needed?

Startup Repair Note: You may need to do startup repair 3 to 4 times.

I'll try doing the F8 thing tonight. I recently wiped my HD and installed Linux alone (formerly a dual-boot set-up) with Win7 in a VM. He didn't like that at all - and suggested I plug the computer directly into the wall, until such time as I can go out and buy a higher-grade surge protector, What To Do After Installing A New Hard Drive If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.Step Two: Remove the

After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. The original 256 MB of Ram is DDR 266MHz, Hynix is a name on it as well as Gateway. Of course, there’s often a big gap between what should happen and what does happen.Let’s see if we can fix this problem.[Have a tech question? news Apple disclaims any and all liability for the acts, omissions and conduct of any third parties in connection with or related to your use of the site.

Click on the Erase tab in the DU main window.5. Generally, soon after you turn on the PC, well before Windows loads, a message similar to “Press F2 for Setup” flashes onscreen. My partition map scheme is GUID Partition Table. I then booted fine into the new Windows and copied over all my files and such.

General Discussion triple boot system installed xp after win7 and 8-boot problemsSo i had a win 7 and 8 dual boot system where partition- 0 was sys reserved 1 was 7 mostly, it must be a cd/dvd that you got along with the computer. windows will take over from there. Load Default Settings13.